Set the LNB and connect the cable to the LNB then seal the connection with waterproof tape. Fasten the cables on to the dish with cable ties. Feed the cable through the roof to the DStv decoder and connect the decoder to the cable that comes from the satellite dish. Connect the decoder to the tv by using the HDMI cable provided with the decoder. I cannot install my own dish as it is a complex. To pay R2000.00 guess I am downgrading to the old silver decoder. No way I am paying R2000.00 just to have access to the dstv explora. Decoder (EXPLORA) or LNB IN (SINGLE VIEW HD). DO NOT CONNECT THE EXPLORA SWITCH (EXPLORA). 2 Plug the power supply into the decoder. 3 The DSTV INSTALLATION WIZARD screen will appear showing STEP 1 of 4. 4 Press OK to select NEXT STEP. 5 STEP 2 of 4 will appear - DON'T CHANGE ANYTHING HERE. 6 Press OK to select NEXT STEP. 7 STEP 3 of 4 will appear. DStv HD DECODER QUICK GUIDE Step 1: Install the DStv Explora Dish and Connect it to the Decoder. Point your DStv dish (90cm) to Eutelsat 36B 36e. If you can’t do this by yourself, call a professional installer. If you installed a dish facing DStv with a single solution universal LNB, please swap your existing LNB with the DStv SLNB.
While it’s always better to get a team of experts or single professional, to install your DSTV dish and set it up for success, there is no harm in doing it yourself. In fact, learning to do it yourself will probably be beneficial for you as that professional won’t be around all the time in case something goes wrong or if your dish ever needs to be adjusted.
Besides, sometimes doing yourself, will give you more assurance that it be done correctly, even if you’re just checking whether the professional does it right.
How to install a DSTV dish yourself
Step one – Mount the dish properly
- When you receive your DSTV dish, you will notice that it comes with four cement screws. The first step will be to drill four holes into the base of the antenna mast, relevant to the mounting location, which will need an unobstructed view pointing to the Eastern part of the sky. You will then screw these cement screws into the drilled holes.
- Once you’ve inserted the screws into the holes, you will place the dish’s antenna assembly on top of its mast. Be sure to pay attention to the centre of the mast that needs to be clamped on the posterior of the dish, as well as align with the top part of the mast’s pole. Now you must tighten the two screws onto the clamp of the mast, for it to remain securely in place.
- Take the RG-6 coaxial cable and plug it into the relevant part of the dish, which after you plug the other end into the port of the decoder, also known as the satellite receiver, connected to your television.
Step two – Align the DSTC dish correctly
- Make use of a sat meter to point the dish in the correct direction.
- Correct the elevation, which is adjustable on the side. You will see degree markers. The best would be to mark it between 36 and 39 degrees.
- By having a look at the dish, adjust the LNB to point at 4 O’clock. Keep testing it for optimal signal quality.
Step three – Ensure stability and enjoy
- Be sure to use something as simple as cable ties to keep the cables on your wall as it won’t wear out.
- Finally, switch on your television, your decoder and enjoy some top-quality entertainment.
Get DSTV installation from Clearsite today!
decoders as well as any installation information available on our website. For more information, visit wiringall.com XtraView – Technical Manual V (August . However, if you do not have a DSTV smart LNB you can use a twin LNB but you will need to purchase a DSTV switch in order to have a successful installation.
This is a guide to control two dstv decoders connected via Xtraview with a There is a diagram available inside the package that shows how to. The recommended installation for the DStv Explora (when installed on its own). 3 UniCable outputs and 1 universal output.
Top» Catalog» DSTV XtraView Installation with SmartLNB & Diagram for Multichoice Explora/HDPVR and other decoders. Please see various examples below of Multichoice Xtraview Configuration guidelines and more advanced installations using a combination of either single view.XtraView Installation Manual wiringall.com p7/33 Public Release 2 CHOOSING AN XTRAVIEW OPTION How many independent viewing points do you need?
3 2. XtraView Installation Manual wiringall.com XtraView Installation Manual wiringall.com RF.
PVR. The recommended installation for the DStv HD Decoder is a single LNB (it will however also work if connected to a twin, quad, UniCable™ or DStv Smart LNB)..
When installed as part of an XtraView setup, we recommend the use of a DStv Smart LNB. A DStv HD .
How To Install Dstv Dish And Decoder Pdf Free
For those who like to understand what is going on we have included a breakdown of the basic wiring categories involved with DSTV. RG6 Coaxial Cable The primary function of coaxial radio-frequency cabling (RG6 is the standard for DSTV) is in carrying the radio frequency signals from the satellite dish to /5.